Why Learning Plumbing Basics is Vital for Bathtub Installation
Why Learning Plumbing Basics is Vital for Bathtub Installation
Blog Article
Are you on the lookout for facts around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't specifically rocket science, however it does require strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bath tub with a brand-new one is likewise a moderately hard task. If the old bathtub is easily obtainable, the job can relocate easily; if you need to open up a wall to remove the old bathtub as well as place the brand-new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the brand-new one. Make certain you have actually qualified on your own for the task and fit trying it. Instead of hiring a professional to take control of a halfway-completed job, it is much better to take into consideration utilizing one before you start. Chances are you might need a specialist plumber to make tube connections.
This write-up will assist you install a brand-new bathtub in your shower room if you have actually already acquired a brand-new bathtub and also do not need to change the arrangement of your previous water system pipelines.
Your devices as well as product list should comprise the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, after that the first thing you must do is separate the water supply. After doing so, activate the taps to drain pipes any kind of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic due to the limited gain access to that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipelines to the faucets. Have a towel prepared for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
Before moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end gives a link to the current supply pipelines.
If you need to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Secure the faucet in place with the supplier given backnut. Once the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous kind must be connected to the tap ends first, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Tub
Utilizing both wood boards under its feet, place the tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards rather than focusing all the weight onto four little factors.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by inspecting the spirit level as well as changing the feet on the bath tub till the level reads degree.
To install faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipeline by making a compression join; after that do the same for the other tap.
Activate the water as well as examine all joints and also new pipework for leakages and also tighten them if required. Fill the bathtub and additionally inspect the overflow electrical outlet and also the normal electrical outlet for leaks.
Finally, fix the bath paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub must wait till the bathtub has been used at the very least when as this will certainly resolve it right into its last placement.
Getting ready for the Installation
To start with, the supporting structure provided with the bathroom needs to be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets system to avoid stress on the bath tub.
Fit the flexible faucet connectors to the bottom of both faucets utilizing 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently be ready to be suited its last position.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to break an inflexible seal, causing the water to permeate the wall surface in between the bathroom and also the tiling, bring about problems with moisture and also feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and installations. They are sold in tubes as well as cartridges, and can sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill the tub with water before sealing, to enable the movement experienced when the tub is in use. The sealer can break rather early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the floor tiles using waterproof or waterproof sticky as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a keen person who reads about How to Install a Bathtub Yourself, I thought sharing that short article was worth the trouble. You should take the opportunity to share this entry if you liked it. I take joy in reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Expert consultation available. Report this page